Shopping Cart is Full

You cannot add any additional items to the Shopping Cart

Close Window

Site will log you out


You are leaving the BEHR® Consumer website. You will be logged out.



Ask an Expert by Email


Thank you,
Your email has been sent to our experts.



See all Products »

BEHR® Barn & Fence Paint

BEHR® Barn & Fence Paint

An advanced exterior paint combining the best features of oil and latex for superior color retention, adhesion, penetration and durability. 

Finish
Flat
Where to Use
Smooth or rough-sawn exterior vertical wood surfaces such as Plywood, Fences, Shingles, Shakes, Siding and Laminates.
Coverage
200-500 Sq. Ft per Gallon

Latest Featured Reviews

Find a Store

Enter your Zip/Postal Code to find the nearest Home Depot

Where to Use

Smooth or rough-sawn exterior vertical wood surfaces such as Plywood, Fences, Shingles, Shakes, Siding and Laminates. Not for use on horizontal surfaces subject to foot traffic. Dry film will not harm livestock.

2-3 HR Dry Time 
6-8 HR
Recoat Time

200-500 Sq. Ft
Coverage per Gallon

Soap & Water
Clean-Up

Protect
from Freezing

Preparation

Proper surface preparation is required

  • Remove stains caused by mold and mildew with a mold and mildew stain removing product.

Previously painted, stained or clear sealed wood

  • Sand all glossy surfaces.
  • If surface is in good condition, apply directly over clean, dry surface.
  • If the latex or oil-based finish has started to crack, peel or flake, use a product such as BEHR PREMIUM® NO. 64 Wood Stain & Finish Stripper on wood to remove the coating. Rinse thoroughly.
  • Follow with a product such as BEHR PREMIUM NO. 63 All-In-One Wood Cleaner. Scrub, rinse, and allow to dry completely.

New, weathered, pressure treated or uncoated wood

  • Place cloth duct tape in random areas on the bare wood. Press the tape firmly then quickly remove it.
  • If wood fibers or debris are pulled onto the tape, the wood surface is not sound and additional preparation is required as follows: Clean surface with a product such as BEHR PREMIUM NO. 64 Wood Stain & Finish Stripper. Rinse.
  • Follow with a product such as BEHR PREMIUM NO. 63 All-In-One Wood Cleaner at full strength to remove mill glaze and/or loose wood fibers, dirt and other debris. Rinse and allow to dry.

Application

  • Use when air and surface temperature are 50-90˚F (10-32˚C).
  • Do not apply in direct sunlight or if rain is expected within 24 hours.
  • Wood surfaces must be completely dry.
  • When working with more than one container of the same color, intermix to ensure color uniformity.
  • Redwood, Cedar, Cypress and other “bleeding” woods contain water soluble extractives which may cause discoloration of white and pastel colors; therefore prime the above type woods with one coat of a product such as BEHR PREMIUM PLUS® NO. 436 Exterior Multi-Surface Primer & Sealer to reduce these stains.
  • Apply with a nylon/polyester brush on smooth surfaces. On rough-sawn or textured wood apply with a 3/4" long nap roller or high quality airless sprayer. For airless spraying use a .015" tip. Keep a wet edge to reduce lapping and help control color uniformity.
  • Always back-brush or back-roll during all application methods.
  • Two coats may be necessary for complete hiding. Apply the second coat only after the first coat has thoroughly dried.

Dry Time

  • Longer dry time required in cooler temperatures and higher humidity.

Disposal

  • For disposal of empty containers and unused product contact your household refuse collection service.

To consult with a BEHR Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).

Other Products You May Like