Behr

Wood Stains & Waterproofers

Where to Use

• Exterior, properly prepared wood and composite surfaces such as: Decks, Railings, Shakes, Shingles, Siding, Roofs, Fences and Furniture.

CAUTION: Stained surfaces may become slippery when wet.

Preparation†

• To remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood decks, siding, fences, shakes and shingles use BEHR® PREMIUM STAIN & FINISH STRIPPER NO. 64.
• Use BEHR® PREMIUM 2-IN-1 WOOD PREP NO. 63 to clean and brighten the wood surface and to remove light to medium stains caused by mold, mildew, algae & fungus. Rinse thoroughly. Allow to dry. Apply coating. On new wood use NO. 63 to remove mill glaze and open the pores of the wood.
• For severe stains caused by mold, mildew, algae & fungus apply BEHR PREMIUM MOLD & MILDEW STAIN REMOVER NO. 62 and rinse prior to applying BEHR PREMIUM 2-IN-1 WOOD PREP NO. 63.

Application

• Do not use if temperature is below 40°F (4.5°C) or if rain is expected within 24 hours.
• Wood surfaces must be completely dry.
• No primer needed on most woods. However, Redwood, Cedar, Cypress and other “bleeding” woods contain water soluble extractives which may cause discoloration of white and pastel colors; therefore, prime the above type woods with one coat of BEHR EXTERIOR WATER-BASED ACRYLIC LATEX PRIMER & SEALER NO. 436. See label for additional instructions.
• When working with more than one container of the same color, intermix to ensure color uniformity. Stir stain before and occasionally during application.
• Use a 3/8” nap roller, nylon/polyester brush, pad applicator or airless sprayer.
• Airless spray is recommended for experienced applicators only. Use a .015 to .017 tip. Thin with water at a rate of no more than 1/2 pint per gallon.
• Spread rate is approximately 200-400 sq. ft. (19-37 m2) per gallon depending on surface texture, porosity and application method.
• Maintain a wet edge when applying. Always back-brush and apply product end to end or to board lengths to prevent lap marks.
• Over-application of stain will lead to surface failure including peeling and cracking. Avoid applying stain too heavily. Do not apply more than two coats.
• For optimum performance, coat all six sides of the wood.

Dry Time

• 24 hours before subjecting surface to light foot traffic, 72 hours to full cure.

Clean Up

• Use soap and water.
• For disposal of unused paint products, please contact your household refuse collection service.

Warranty

*LIMITED WARRANTY Behr Process Corporation warrants customer satisfaction with this product for 15 years on vertical surfaces and for 5 years on horizontal surfaces from date of purchase, when applied to a properly prepared surface according to label directions. Color fading and slight natural graying of the wood may occur during this period, especially in areas exposed to heavy foot traffic or excessive weather. If you are not satisfied with this product, Behr Process Corporation will, at its option and upon proof of purchase, either furnish an equivalent amount of new product or refund the purchase price. This warranty is made to the original residential product purchaser and is not transferable. This warranty excludes (1) labor and costs of labor for application or removal of any product or (2) any incidental or consequential damages, whether based upon breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Important!

IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS.

Warning

† WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.

WARNING! This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

WARNING! IRRITANT! HARMFUL IF SWALLOWED. CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air.  If properly used, a respirator (NIOSH approved for organic vapor with P Series particulate prefilter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately. CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.

To consult with a BEHR Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).

©2009 BEHR PROCESS CORPORATION Santa Ana, CA 92704 U.S.A. www.behr.com V.O.C. (C.O.V.) <100 g/L REV. 3/09