Behr

Application Assets

Where to Use

• Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces.

Preparation†

(The following steps are recommended for best results.)

• Allow new stucco, plaster and masonry to cure for 30 days.
• CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with a product such as BEHR PREMIUM™ CONCRETE & MASONRY DEGREASER & CLEANER NO. 990. Remove mildew stains with a mildew stain removing product. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with a product such as BEHR PREMIUM CONCRETE & MASONRY CLEANER & ETCHER NO. 991. Follow all label instructions.
• PRIME: Use a product such as BEHR® 100% ACRYLIC PRIMER & SEALER N0. 436 or a product such as BEHR OIL-BASED PRIMER & SEALER N0. 434. Follow all label instructions.

Application

• DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40–90°F (4-32°C).
• Apply a thin coat using a high quality china bristle brush, 1/4-3/8” nap roller or an airless sprayer (.013-.015 spray tip) at a spread rate of 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces.

Dry Time

• Dries to the touch in 4-5 hours. Longer dry time required in cooler temperatures and higher humidity. Recoat in 24 hours. Wait at least 7 days before rinsing or cleaning the surface with a mild, non-abrasive detergent.

Clean Up

• Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing.
• For disposal of empty containers and unused product, contact your household refuse collection service.

Warranty

LIMITED WARRANTY BEHR PROCESS CORPORATION warrants that this product meets Behr’s manufacturing specifications. If this product does not meet these specifications, Behr Process Corporation will, at its option and upon proof of purchase, either furnish an equivalent amount of new product to you or refund the purchase price of this product.This guarantee excludes (1) labor and costs of labor for application or removal of any product; or (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Important!

IMPORTANT: DO NOT OPEN CONTAINER WITHOUT READING INSTRUCTIONS. PROTECT FROM FREEZING.
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS

IMPORTANT! STORAGE AND DISPOSAL: DANGER! Rags, steel wool and waste soaked with this BEHR OIL-BASE High-GLOSS ENAMEL may spontaneously catch fire if improperly discarded or stored. To avoid a spontaneous combustion fire, immediately after use, place rags, steel wool or waste in a sealed, water-filled, metal container. Do not store unused product inside the home. For disposal guidance, contact your household refuse collection service, fire department, county or state government environmental control agency.

Warning

† WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.

WARNING! This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

DANGER! COMBUSTIBLE LIQUID AND VAPOR. CONTAINS PETROLEUM DISTILLATES AND ALKYD RESIN. VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION. NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain or nervous system damage. Intentional misuse by deliberately concentrating and inhaling contents may be harmful or fatal. Keep away from heat and flame. Do not smoke. Close container after each use. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. Do not use in an unventilated area. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate prefilter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If swallowed, do not induce vomiting. Call a physician immediately. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.

To consult with a BEHR Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).