Shopping Cart is Full

You cannot add any additional items to the Shopping Cart

Close Window

Site will log you out

You are leaving the BEHR® Consumer website. You will be logged out.

Ask an Expert by Email

Thank you,
Your email has been sent to our experts.

See all Products »

Extra Textured DECKOVER® No. 5015

Extra Textured DECKOVER® No. 5015

Bring new life to old wood and concrete surfaces with BEHR PREMIUM EXTRA TEXTURED DECKOVER. This 100% acrylic formula conceals cracks and splinters up to 1/4", and creates a heavily textured, slip-resistant finish that provides waterproofing protection. It's available in 54 solid custom colors, and is also great for decks, railings, patios, composite decks, pool decks and walkways.


View DeckOver Colors.


Creates a textured, slip-resistant finish
Where to Use
For properly prepared exterior weathered or cracked horizontal and vertical wood, concrete and composite surfaces.
1st Coat 75 Sq. Ft; 2nd Coat 75 Sq. Ft.

Latest Featured Reviews


WoodSmart by Behr

Learn about product selection, preparation, and how to's for your stain project with WoodSmart by Behr.

Start Woodsmart >>

Tools & Resources

SDSs, Tech Data & Certifications

Available In

Where to Use

Recommended for properly prepared interior and exterior weathered or cracked horizontal and vertical wood and composite surfaces such as Decks, Railings, Porches and Boat Docks. Also great for concrete surfaces such as Pool Decks, Patios and Sidewalks. Do not use on drivable surfaces such as garage floors.


Usage Summary

Must Prep

Before Use

2 Coats Required

Horiz. Spread Rate:
1st Coat 75 Sq. Ft
2nd Coat 75 Sq. Ft.


Soap & Water

Surface Preparation†

Proper surface preparation is required.

  • All surfaces must be clean, sound, dry and free of any dirt, oil and grease before application.



  • Replace rotting or splitting boards and remove loose splinters.
  • To remove failing coatings or to remove loose wood fibers, use a product such as BEHR PREMIUM® No. 64 Wood Stain & Finish Stripper followed by BEHR PREMIUM No. 63 All-In-One Wood Cleaner to neutralize the wood. 
  • When stripping is not needed, the surface MUST be prepared with a product such as No. 63 Wood Cleaner to remove mill glaze and clean the wood surface. 
  • After using either No. 64 or No. 63, rinse thoroughly with a garden hose or pressure washer. When rinsing with a pressure washer, use the broadest spray pattern while keeping the nozzle at least 24" away from the surface. 
  • Allow the area to dry at least 24 hours before coating. 
  • If needed, lightly sand to remove any wood fibers/fuzz. 



  • Avoid areas that are structurally weak or subject to hydrostatic pressure above 8 psi. 
  • Allow new surfaces to cure for 30 days. 
  • Clean and etch surface using a product such as a muriatic acid etcher to achieve a textured profile similar to 150 grit sandpaper. 
  • If the previous coating is failing or peeling, use a paint stripper to remove old coating.


  • Use product when air and surface temperatures are between 50-90˚ F (10-32˚ C). 
  • Avoid applying in direct sunlight or to hot surfaces. 
  • Do not use if rain is expected within 24 hours. 
  • The surface must be completely dry before application. 
  • Avoid painting if humidity is expected to be greater than 80%. 
  • Intermix multiple containers to ensure color uniformity. 
  • Stir product occasionally throughout application.  May thin with up to 8 oz. of clean water per gallon.
  • For nail holes and cracks up to 1/4", completely fill in with Extra Textured DECKOVER® coating using a nylon/polyester brush and allow to dry prior to rolling. 
  • Deep nail holes and cracks may require additional filling. 
  • For edges, corners and in between wood boards, apply using a nylon/polyester brush. 
  • Use pressure while rolling and apply a generous, even coat using the DECKOVER Extra Textured Roller Cover. 
  • For vertical surfaces such as railings, use a nylon/polyester brush or roller and apply two thin coats at a spread rate of 400 sq. ft. per gallon. 
  • Do not use with airless sprayer. 
  • For optimum performance, film uniformity, leveling and to cover cracks, a second coat MUST be applied. 
  • Maintain a wet edge when applying.

Dry Time

  • 4-6 hours before recoat. 
  • Dries to touch in 4 hours. 
  • Wait 24-48 hours before light foot traffic. 72 hours to full cure. Additional dry time may be needed in cooler temperatures and higher humidity. 
  • Premature heavy traffic will cause coating failure.



  • For disposal of empty containers and unused product contact your household refuse collection service.

To consult with a Behr Certified Coatings Professional, call Behr Pro Hotline Toll Free number at 1-877-776-3961 (U.S.A. only).