BEHR® FAST DRYING OIL-BASED POLYURETHANE AEROSOL

Average Rating:
false

BEHR Fast Drying Oil-Based Polyurethane Aerosol is a clear protective finish that shields your interior wood surfaces that are stained with BEHR Oil-Based Wood Stain. This durable polyurethane is designed to prolong the life of your wood surface and create a smooth, lasting finish. This product enhances the look and color of your wood surface, allowing its true beauty to shine through. Multiple sheens are available depending on your desired look.

See Our Selection of Interior Oil-Based Stains and Finishes.

Finish
Available in Matte, Satin, Semi-Gloss and Gloss Finishes.
Best for use in
Properly prepared interior unfinished and finished wood surfaces such as furniture, moldings, cabinets, trim and doors.
Coverage
15 - 20 Sq. Ft.

Read important application instructions to ensure optimum paint performance.

Pink and purple colored brush strokes

Find Your Perfect Color!

Find, Coordinate & Preview Paint Colors

Explore our color library. Browse our collections of popular and trending colors.  Find coordinating colors then preview them in your own virtual room image. Do it all with ColorSmart by BEHR®.

Explore Color Now

Sold Exclusively at
The Home Depot

Find a Home Depot store near you.

Light blue and light green brush strokes

Product Usage

3 Coats
Required

Spread Rate:
15-20 Sq. Ft.

Clean-Up
Mineral Spirits

Where to Use

Properly prepared interior unfinished and finished wood surfaces such as furniture, moldings, cabinets, trim and doors.

Usage Summary
Surface Preparation

The following steps are recommended for the best results.

  • For refinishing, remove all wax or cleaner build-up with a wax stripper or degreaser prior to sanding.
  • Sand all surfaces in the direction of the wood grain to desired smoothness.
  • DO NOT USE steel wool.
  • Remove all dust from sanded surfaces and clean with a tack cloth.
  • If desired, apply BEHR® Wood Stain. Follow all label instructions.
Application
  • Do not apply in direct sunlight or in temperatures below 55°F (10°C) or above 90°F (32°C). 
  • Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use.
  • Protect adjacent areas from overspray. Wet overspray can be removed with mineral spirits.
  • Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes. On unfinished wood, apply sufficient material to seal open joints, edges, and end-grain.
  • Apply thin coats to avoid runs and sags. Recoat within 2-4 hours. If unable to do so, wait a minimum of 72 hours, then lightly sand and recoat.
  • Apply at least 3 coats on unfinished wood and 2 coats on surfaces already finished.
  • After final coat, allow at least 24 hours before normal use.

NOTE: Above dry times are based on good ventilation, the temperature of 77°F and 50% relative humidity. Lower

temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an

inconspicuous area to ensure satisfactory results.

Nozzle Care
  • After each use, clear valve by holding can upside down and spraying until only clear gas comes out.
  • If the spray button becomes clogged, wear eye protection, wipe off button opening with lacquer thinner.
  • Do not stick a pin in spray button opening.

Read Application Instructions

LIMITED WARRANTY

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event this product proves to be defective within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Read Warranty Information

  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 145ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;