Shopping Cart is Full

You cannot add any additional items to the Shopping Cart

Close Window

Site will log you out


You are leaving the BEHR® Consumer website. You will be logged out.



Ask an Expert by Email


Thank you,
Your email has been sent to our experts.



See all Products »

BEHR® DRYPLUS™ Masonry Waterproofer

BEHR® DRYPLUS™ Masonry Waterproofer

BEHR® DryPlus™ No. 875 is an advanced Interior/Exterior masonry waterproofer designed for porous concrete surfaces.


Ideal for basement and retaining walls.
 

Click Here to see available colours.

Finish
Flat Finish
Where to Use
Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks.
Coverage
7 - 12 m2 per 3.73 L

Latest Featured Reviews

There are currently no featured reviews for BEHR® DRYPLUS™ Masonry Waterproofer
READY TO USE OR ADD TINTING COLOURANTS

Find a Store

Enter your Zip/Postal Code to find the nearest Home Depot

MSDS & Data Sheet

Where to Use

Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks.

Usage Summary

2 Coats Required
for Optimal Durability

Spread Rate:

Rough 7-9 m2

Smooth 9-12 m2

Dry Time:

1 HR Dry to Touch
4 HR Recoat

Clean-Up:

Soap & Water

Preparation

Proper surface preparation is required

  • New or Unpainted Surfaces: New concrete must cure 30 days. Test for loose concrete by pressing masking/cellophane tape on surface, then pull off abruptly. If the tape doesn’t remove concrete, it can be painted. If concrete is removed, scrape down to a sound substrate.
  • Below grade application: Patch all holes or cracks with a fast setting hydraulic cement.
  • Above grade application: Remove mildew stains with a mildew stain removing product. All surfaces must be clean, free of dirt, efflorescence and oil. Clean surface with a product such as BEHR PREMIUM™ NO. 991 Cleaner & Etcher.
  • Previously Painted Surfaces: BEHR PREMIUM DryPlus NO. 875 provides best results on bare/untreated surfaces. PREVIOUSLY PAINTED SURFACES IN GOOD CONDITION MAY BE PAINTED. HOWEVER, BEHR WILL NOT GUARANTEE RESULTS. Test for loose concrete as stated under “New/Unpainted Surfaces” above. Remove deteriorated coatings. Follow all prep instructions under “New/Unpainted Surfaces” above.

Application

  • Stir well before use.
  • Do not thin or apply at greater spread rate.
  • Use with adequate ventilation.
  • Use product when air/surface temperature is 10-32° C. Apply to dry or slightly damp surfaces. Wipe off any moisture before painting. Apply with a 13-19 mm nap roller, 4 cm nylon/polyester brush or an airless sprayer @ 155-225 kg/cm2 (2,200-3,200 lbs/in²) PSI using a .023 -.025 spray tip.
  • Two coats minimum are required: First Coat: Use a brush or roller, work onto the surface covering all pores or voids. Repeat for 2nd coat. Spot application may be needed depending on porosity.
  • Important: If leaking persists after 2 coats, it indicates voids and pinholes are still open. Reapply to area.

Dry Time

  • Low temperatures or high humidity conditions will affect drying time.
  • Full cure should be reached in 7-14 days.

Disposal

  • For disposal of empty containers and unused product contact your household refuse collection service.

To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.

Other Products You May Like