Shopping Cart is Full

You cannot add any additional items to the Shopping Cart

Close Window

Site will log you out

You are leaving the BEHR® Consumer website. You will be logged out.

Ask an Expert by Email

Thank you,
Your email has been sent to our experts.

See all Products »

BEHR PREMIUM® Decorative Concrete Dye No. 863

BEHR PREMIUM® Decorative Concrete Dye No. 863

A unique decorative finish that will transform ordinary interior/exterior concrete into an elegant floor resembling marble or glazed stone. Concrete Dye is a water-based acid free finish and provides consistent color accuracy. It is available in 36 individual dye colors and it allows you to create your own custom color blends.

See How-To video.

Resembles marble or glazed stone.
Where to Use
Uncoated and unsealed, properly prepared Interior or Exterior concrete surfaces such as: Patios, Porches, Pavers, Walkways, Kitchens, Bedrooms and other concrete floors.
175-250 Sq. Ft. Base Color; 350-500 Sq. Ft. Accent Color

Latest Featured Reviews


SDSs, Tech Data & Certifications

Where to Use

Uncoated and unsealed, properly prepared Interior or Exterior concrete surfaces such as: Patios, Porches, Pavers, Walkways, Kitchens, Bedrooms and other concrete floors. 

Usage Summary

Apply With

Pump Sprayer

Spread Rate:

Base Color

175-250 Sq.Ft.

Accent Color

350-500 Sq. Ft.

Dry Time:

1-2 HR Dry to Touch

for Dyes

24 HR Before Clear

Top Coat Applied

Must Use With

Etcher & Sealer

Where Not to Use

DO NOT use on Garage Floors, Driveways, around Swimming Pools or on concrete that is subjected to high levels of moisture.


Proper surface preparation is required.

  • New concrete must cure for a minimum of 30 days.
  • Protect surrounding areas. Do not apply tape to surfaces that have been coated with the dyes or sealer as the adhesives may remove the coatings.
  • For proper penetration and adhesion, must etch with concrete & masonry cleaner & etcher product.
  • Remove severe stains using a concrete & masonry degreaser & cleaner product.
  • The floor must be thoroughly cleaned, completely rinsed, and dry. For interior application, use a mop and bucket to rinse and clean.
  • Important: Failure to completely rinse the concrete surface may result in adhesion issues.

Pump Sprayer

  • BEHR PREMIUM Decorative Concrete Dye must be applied with a high quality pump sprayer with a conical tip.
  • Do not use a pump sprayer with a fan tip.
  • Read all manufacturers’ assembly and operating instructions carefully before using the pump sprayer.
  • When not in use, soak the tip of the pump sprayer in water to prevent the tip from becoming clogged.


  • DO NOT THIN. Stir product in can before pouring into the pump sprayer.
  • Use product when air and surface temperatures are between 50–90° F (10-32° C).
  • Do not apply if heavy winds are blowing or if rain is expected within 24 hours. Important: Test a small inconspicuous area to ensure color satisfaction.


First Color (BASE COLOR):

  • A light tone color is ideal for a base color.
  • Fill the pump sprayer with first color and fully pressurize.
  • Tip: Adjust the pump sprayer nozzle tip until you reach a fine mist setting. Practice spraying on a piece of cardboard or newspaper.
  • Apply Concrete Dye using a random or figure eight motion.
  • Refrain from covering the concrete surface with an even, steady stream as this could lead to a monochromatic look rather than a variegated look.
  • Hold the spray tip approximately 10 inches above the concrete surface.
  • If you need to stop during application step, use natural break points such as borders, walls or expansion joints.
  • Important:To prevent drips from getting on the surface, use a rag to catch any drips when stopping the sprayer.
  • Allow first color (Base Color) to dry to the touch before applying a second color (Accent Color).
  • Do not walk on wet Dyes.
  • Save any unused product for future touch-ups.


Second Color (ACCENT COLOR):

  • A dark tone color is ideal for an accent color
  • Flush pump sprayer and wand out with fresh water.
  • Add second color to clean pump sprayer and fully pressurize.
  • Apply second color in a light random pattern.
  • Be careful not to cover first color completely.



  • To complete the project and add a clear protective finish, it is required to apply a product such as BEHR PREMIUM No. 985 Wet-Look Sealer.
  • Flush pump sprayer and wand out with fresh water.
  • Allow dyes to dry 24 hours before applying Wet-Look Sealer
  • Add Wet-Look Sealer to a clean pump sprayer, fully pressurize then apply.
  • Follow all label instructions

Clean Up

  • Properly dispose of all soiled rags.
  • For disposal of empty containers and unused product contact your household refuse collection service.

To consult with a Behr Certified Coatings Professional, call Behr Pro Hotline Toll Free number at 1-877-776-3961 (U.S.A. only).

Other Products You May Like