BEHR PREMIUM^® SPRAY PAINT

UPGRADE THE WAY YOU SPRAY

Your favorite Behr colors, now in a spray can.

Buy Now

Features

Corrosion and Rust Resistant for Indoor/Outdoor Use
Drip & Run Resistant Formula
Excellent Adhesion on Wood, Metal, Plastic, Cast stone, and more
Great Hide & Coverage
Ergonomic Can Shape & Comfortable Spray Actuator

Why Choose BEHR PREMIUM^® SPRAY PAINT?

Close up of Behr Premium Spray Paint's comfortable spray actuator

Ergonomically Designed Can & Comfort Spray Tip

Excellent Adhesion to Multiple Substrates

Close up of spray painted cabinet door showcasing advanced hide

Advance Hide covers underlying surface

AVAILABLE PRODUCT

Choose from 24 colors

BEHR PREMIUM^® Spray Paint

Avg. Rating:

Learn More

PRODUCT USAGE AND APPLICATION INSTRUCTIONS
PRODUCT USAGE
Where to Use
Use on properly prepared surfaces such as:

Wood

Metal

Plastic

Cast stone

Wicker

Preparation

The surface must be clean, free of dust, grease,wax, peeling paint, mold or mildew. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.

†Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.

* Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before painting.

†WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.

empty-paragraph

Read More

Application

Eye protection is recommended.

For best results, use at room temperature. Cover adjacent areas to protect from overspray.

Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use. Hold can upright, moving from side-to-side while spraying lightly and evenly about 12" from the area being painted. 2 to 3 thin coats produce best results.

Apply thin coats to avoid runs and sags. Recoat within 1 hour or after 24 hours.

Dries to touch in 15-30 min. Cooler temperatures or higher humidity may prolong drying time.

Use Behr^® Primer for enhanced performance on porous surfaces or rough wood.

Read More

Clean-up & Disposal

Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released. If spray nozzle becomes clogged, remove and clean.

Do not stick pins or wire into can opening.

Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint with paint remover, but test small area first to ensure paint remover does not damage substrate

Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

Read More
Read More
SDS & DATA SHEET

SDS & DATA SHEET

BEHR PREMIUM^® Spray Paint

Baronial Brown Gloss Black Gloss Black Matte Black Satin Blue Bandana Gloss Citrus Orange Gloss Congo Gloss Dark Truffle Flat Desert Coral Flat Deep Espresso Satin Flirt Alert Gloss Hidden Sea Glass Gloss Inked Gloss Iron Mountain Satin Luck of the Irish Gloss Lunar Surface Flat Lunar Surface Gloss No More Drama Gloss Ocean Abyss Gloss Orion Gray Gloss Sugary Pink Gloss Summer Sun Flat Toasty Gray Gloss Tree Top Green Gloss Tropics Gloss Unmellow Yellow Gloss White Gloss White Matte White Satin
See Full SDS, Product Data & Safety

See Full SDS, Product Data & Safety
WARRANTY

WARRANTY

For one year from the date of purchase, Behr Process LLC warrants to the original consumer purchaser, (1) that the product meets Behr Process LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

PRODUCT USAGE AND APPLICATION INSTRUCTIONS
SDS & DATA SHEET
WARRANTY

PRODUCT USAGE

Where to Use

Use on properly prepared surfaces such as:

Wood
Metal
Plastic
Cast stone
Wicker

Preparation

The surface must be clean, free of dust, grease,wax, peeling paint, mold or mildew. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
†Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.
* Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before painting.

†WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.

empty-paragraph

Application

Eye protection is recommended.
For best results, use at room temperature. Cover adjacent areas to protect from overspray.
Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use. Hold can upright, moving from side-to-side while spraying lightly and evenly about 12" from the area being painted. 2 to 3 thin coats produce best results.
Apply thin coats to avoid runs and sags. Recoat within 1 hour or after 24 hours.
Dries to touch in 15-30 min. Cooler temperatures or higher humidity may prolong drying time.
Use Behr^® Primer for enhanced performance on porous surfaces or rough wood.

Clean-up & Disposal

Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released. If spray nozzle becomes clogged, remove and clean.
Do not stick pins or wire into can opening.
Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint with paint remover, but test small area first to ensure paint remover does not damage substrate
Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

BEHR PREMIUM^® Spray Paint

Baronial Brown Gloss Black Gloss Black Matte Black Satin Blue Bandana Gloss Citrus Orange Gloss Congo Gloss Dark Truffle Flat Desert Coral Flat Deep Espresso Satin Flirt Alert Gloss Hidden Sea Glass Gloss Inked Gloss Iron Mountain Satin Luck of the Irish Gloss Lunar Surface Flat Lunar Surface Gloss No More Drama Gloss Ocean Abyss Gloss Orion Gray Gloss Sugary Pink Gloss Summer Sun Flat Toasty Gray Gloss Tree Top Green Gloss Tropics Gloss Unmellow Yellow Gloss White Gloss White Matte White Satin

See Full SDS, Product Data & Safety

WARRANTY

For one year from the date of purchase, Behr Process LLC warrants to the original consumer purchaser, (1) that the product meets Behr Process LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.