BEHR PRO® Fast Drying Water-Based Polyurethane Floor Finish

For use on interior residential wood floors, bare wood, stained or previously finished wood, old/reclaimed wood.

NOT RECOMMENDED FOR: Linoleum, vinyl, glazed tiles and metal.

CAUTION: Top coated surfaces may be slippery when wet.

• Prep Before Use
• 3 Coats Required. 4 Coats if Desired
• Spread Rate: 500 Sq. ft./Gal.
• Clean-Up Soap & Water

Surface Preparation

Previously Finished Surfaces:

• For best results, surface must be clean, dry and free of wax, grease, oil, shellac, lacquer, mildew and polishes.
• Waxes must be removed with a wax stripper, sanding does not remove wax.
• Shellac must be removed with a paint stripper.
• Previously finished floors in good condition should be cleaned with a TSP (Tri Sodium Phosphate) solution in water and rinsed thoroughly with clean water.
• Do not use TSP on bare wood floors as discoloring will occur.
• Some types of pre-finished factory finished flooring may not be compatible with Behr Polyurethane Floor Finish (test in an inconspicuous area for compatibility).
• Old finishes in poor condition must be removed.
• If sanding old finish, remove all sanding dust with a vacuum or cloth dampened with mineral spirits.

Stained or Painted Wood:

• Follow manufacturer’s directions for application of stain or paint.
• Make sure surface is thoroughly dry before applying Behr Polyurethane Floor Finish.
• Refer to manufacturer’s label for dry times.
• For best results use Behr Fast Drying Water-Based Wood Stains and finishes.

Unfinished surface preparation:

• Sand all wood surfaces in the direction of the wood grain to desired smoothness.
• Remove all sanding dust with a vacuum followed by wiping with a cloth dampened with water.

Application

• Stir thoroughly before and during use.
• To prevent bubbles in the finish DO NOT SHAKE. DO NOT THIN.
• Do not apply in direct sunlight or in temperatures below 50 degrees above 90 degrees.
• If a wood stain color is desired before applying Behr Water-Based Polyurethane Floor Finish, then use Behr Fast Drying Water-Based Wood Stain.
• Follow all label instructions.
• When applying Behr Water-Based Polyurethane Floor Finish use a high quality nylon/polyester bristle brush or a synthetic pad applicator for larger areas.
• Do not apply with a roller.
• Always maintain a wet edge to avoid lap marks.
• For maximum durability, 3 coats are required, 4 coats if desired.
• Apply thin coats, do not allow puddling.
• Allow finish to dry at least 1 hour between coats but less than 8 hours
• A light sanding between coats is not required, but if a maximum smooth finish is desired, allow 1-2 hours for each coat to dry before lightly sanding with 220-320 grit sandpaper.

Dry Time

• Dries to touch in 1 hour.
• Sand or Recoat allow 1-2 hours.
• After final coat allow 12-24 hours to dry before light use.
• Fully cured 3 days after final coat.

Disposal

• For disposal of empty containers and unused product, contact your household refuse collection service.

For one year from the date of purchase, Behr Process LLC warrants to the original consumer purchaser, (1) that the product meets Behr Process LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event this product proves to be defective within one year from the date of purchase, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.