BEHR PREMIUM® Transparent Waterproofing Wood Finish

Must Prep Before Applying Wood Finish

2 Thin Coats Required

Spread Rate:
1st Coat
300-350 Sq. Ft
2nd Coat
600-700 Sq. Ft.

Soap & Water Clean-Up

Recommended for properly prepared new to slightly weathered, unsealed exterior wood surfaces (0-5 years exposure) such as: Decks, Railings, Shakes, Shingles, Siding, Roofs, Fences and Wood Patio Furniture.

Preparation

• Use a product such as BEHR PREMIUM® No. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
• BEHR PREMIUM® No. 63 All-In-One Wood Cleaner MUST be used following No. 64 to clean, brighten & neutralize wood.
• When No. 64 is not needed, use a product such as No. 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold, mildew, algae & fungus.
• On new wood, use a product such as No. 63 to remove mill glaze and open the pores of the wood. Rinse thoroughly and allow to dry before coating. Lightly sand to remove remaining wood fibers/fuzz.

Application

• Must apply between 40-90˚F (4.5-32˚C). Do not use if rain is expected within 24 hours. The wood surface must be completely dry before application.
• Intermix multiple containers to ensure color uniformity. DO NOT THIN PRODUCT.
• Stir product occasionally throughout application. Test product for penetration and color on a small hidden area before proceeding.
• Use a nylon/polyester brush for areas requiring more accuracy. Use of rollers should be limited to rough surfaces only.
• Use 3/8” nap or longer when appropriate. A high quality pump sprayer with a variable tip or an airless sprayer with a .015 - .019" tip may be used.
• Work in small sections lightly saturating the surface and immediately back-brush or use pad applicator to eliminate puddling, remove excess and evenly distribute the finish.
• Maintain a wet edge when applying. Apply product end-to-end or to board lengths to prevent lap marks.
• Over application of finish will lead to surface failure including peeling and cracking. Avoid applying finish too heavily. For optimum performance, coat all six sides of wood.

Dry Time

• 1-2 hours before recoat. Allow 72 hours for full cure.

Disposal

• For disposal of empty containers and unused product, contact your household refuse collection service.

Behr Process LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for 8 years on vertical surfaces and 6 years on horizontal surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Color fading and slight natural graying of the wood may occur during the warranty period, especially in areas exposed to heavy foot traffic or excessive weather. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.