BEHR PREMIUM^® Solid Color Waterproofing Stain & Sealer

Features you'll love

• Available in 1600 custom colors
• UV Protection
• Rain Protection
• Winter Protection

Product Specs

Must Prep Before Staining

2 Thin Coats Recommended

Spread Rate:
1st Coat
200-400 Sq. Ft
2nd Coat
400-800 Sq. Ft.

Soap & Water Clean-Up

Where to Use

Recommended for properly prepared new to heavily weathered or cracking wood surfaces (0 to 15+ years exposure) such as: Decks, Railings, Shakes, Shingles, Siding, Roofs, Fences, Wood Patio Furniture and Composites.

How to Use

Preparation

• Use a product such as BEHR PREMIUM® No. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood. BEHR PREMIUM® No. 63 All-In-One Wood Cleaner MUST be used following No. 64 to clean, brighten & neutralize wood.
• When No. 64 is not needed, use a product such as No. 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold, mildew, algae & fungus. Rinse thoroughly and allow to dry before coating.
• On new wood, use a product such as No. 63 to remove mill glaze and open the pores of the wood. Lightly sand to remove remaining wood fibers/fuzz.

Application

• Must apply between 35-90˚F (1.7-32˚C).
• Coating will resist rain after 4 hours. The wood surface must be completely dry before application.
• No primer needed on most woods. However, Redwood, Cedar, Cypress and other "bleeding" woods contain water soluble extractives which may cause discoloration of white and pastel colors; therefore prime the above type woods with one coat of a product such as BEHR PREMIUM PLUS® NO. 436 Exterior Multi-Surface Primer & Sealer. See label for additional instructions. Intermix multiple containers to ensure color uniformity.
• Stir product occasionally throughout application.
• Use a 3/8” nap roller, nylon/polyester brush, pad applicator or airless sprayer. Airless spray is recommended for experienced applicators only; use a .015 - .019" tip.
• If thinning is required, thin with water at a rate of no more than 1/2 pint per gallon.
• Maintain a wet edge when applying.
• Always back-brush and apply product end to end or to board lengths to prevent lap marks. Over application of stain will lead to surface failure including peeling and cracking. Avoid applying stain too heavily.
• For optimum performance, coat all six sides of the wood.

Dry Time

• 1-2 hours before recoat. Wait 24-48 hours before light foot traffic. 72 hours for full cure.

Safety and Data Sheets

Warranty

Behr Process LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for 25 years on vertical surfaces and 10 years on horizontal surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Color fading and slight natural graying of the wood may occur during the warranty period, especially in areas exposed to heavy foot traffic or excessive weather. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

https://main--behr--mascocg.aem.page/fragments/related-stain-how-to