BEHR® Solid Color House & Fence Wood Stain

Must Prep Before Staining

2 Thin Coats Recommended

Spread Rate:
1st Coat
200-400 Sq. Ft
2nd Coat
250-500 Sq. Ft.

Soap & Water Clean-Up

DO NOT USE ON HORIZONTAL SURFACES SUBJECT TO FOOT TRAFFIC. Use BEHR PREMIUM Solid Color Waterproofing Stain & Sealer.

Preparation

• Use a product such as BEHR PREMIUM® No. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
• BEHR PREMIUM® No. 63 All-In-One Wood Cleaner MUST be used following No. 64 to clean, brighten & neutralize wood.
• When No. 64 is not needed, use a product such as No. 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold, mildew, algae & fungus.
• Rinse thoroughly and allow to dry before coating. On new wood, use a product such as No. 63 to remove mill glaze and open the pores of the wood. Lightly sand to remove remaining wood fibers/fuzz.

Application

• Must apply between 40-90˚F (4.5-32˚C). Do not use if rain is expected within 24 hours. The wood surface must be completely dry before application.
• No primer needed on most woods. However, Redwood, Cedar, Cypress and other “bleeding” woods contain water soluble extractives which may cause discoloration of white and pastel colors; therefore prime the above type woods with one coat of a product such as BEHR PREMIUM PLUS® NO. 436 Exterior Multi-Purpose Primer & Sealer.
• See label for additional instructions. Intermix multiple containers to ensure color uniformity
• Apply with a nylon/polyester brush. On rough-sawn or textured wood apply with a 3/4” (19 mm) long nap roller or high quality airless sprayer.
• For airless spraying use a .015 - .019" tip. Pump Sprayer not recommended. Always back-brush or back-roll during all application methods.
• Keep a wet edge to reduce lapping and help control color uniformity.
• Over application of stain will lead to surface failure including peeling and cracking. Avoid applying stain too heavily.
• Two coats may be necessary for complete hiding. Apply a thinner second coat after the first coat has thoroughly dried.

Disposal

• For disposal of empty containers and unused product, contact your household refuse collection service.

Behr Process LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for 10 years on vertical surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED, VERTICAL SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Color fading and slight natural graying of the wood may occur during the warranty period, especially in areas exposed to heavy foot traffic or excessive weather. This warranty is not transferable. If this product is found not to perform as specified on the label, during the warranty period, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.