BEHR ULTRA™ Exterior Satin Enamel

Where to Use

Properly prepared and cleaned coated or uncoated exterior surfaces. Ideal for Wood, Vinyl,Aluminum, Fiber Cement Siding,Metals, Steel, Doors, Windows, Trim, Shutters, Garage Doors,Outdoor Furniture, Railing and Wrought Iron.

Usage Summary

Preparation & Prime†

• Countersink nailheads, fill and sand smooth. Remove rust, loose or peeling paint. Repair imperfections and sand smooth.
• Wash off dirt, grease and chalk with detergent and/or powerwash. Remove mildew stains with a mildew stain removing product.
• Clean and sand new or weathered wood. Scuff sand or degloss smooth or glossy surfaces.
• Scuff sand or etch metals. Rinse and allow to dry.
• Caulk windows, doors and other openings. Allow new stucco, plaster and masonry to cure for 30 days before painting.
• Use BEHR PREMIUM PLUS ULTRA® paint as a primer for repaired or uncoated surfaces, including woods that contain tannins (two primer coats required for redwood and cedar) and heavily stained areas.
• Lock in stains with the first primer coat; if necessary, apply a second primer coat of BEHR PREMIUM PLUS ULTRA.
• For drastic color changes or when applying deep colors denoted with a dagger (†) on the color chip, apply a tinted primer coat of BEHR PREMIUM PLUS ULTRA if needed.

Application

• Apply product on dry substrates when air and surface temperatures are between 35°-90°F (2°-32°C) and will remain between 35°-90°F (2°-32°C) for at least 4 hours after applying.
• Do not paint when rain or heavy condensation is expected.
• Stir paint occasionally. Intermix containers of same product to ensure color and sheen uniformity.
• On semi-smooth surfaces, use a high quality 3/8-1/2” nap roller cover, nylon/polyester brush or an airless sprayer (.015-.021” spray tip, 60 mesh filter).
• On rough surfaces, use a high quality 3/4-1” nap roller cover.
• Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 1/2 pint per gallon.
• Certain colors may require more than one coat for complete hide.
• On heavy stains and woods that contain tannins, allow 12-16 hours of dry time between coats. Cooler temperatures or higher humidity may prolong drying time.
• After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
• Dry paint film is mildew resistant.
• When applying to vinyl, color choice must be the same color or lighter than the existing color. Do not use on floors.

Disposal

• For disposal of empty containers, unused paint and soiled rags, contact your household refuse collection service.

Visit behr.com for painting tips, expert project advice and the perfect color coordination with COLORSMART BY BEHR™.

Behr Process Corporation warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey:  The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.