BEHR PREMIUM^® Porch & Patio Floor Paint - Low-Lustre Enamel

Where to Use

On properly prepared, previously painted or primed Interior or Exterior surfaces. Ideal for Porches, Floors, Decks, Basements, Patios, Siding, Trim, Furniture and Trellises. Not for use on Garage Floors.

Usage Summary

Preparation†

Proper Surface Preparation is required.

• All surfaces must be clean, sound, dry and free of any dirt, oil and grease.
• Remove mildew stains with a mildew stain removing product.
• New or Weathered Wood: use a product such as BEHR PREMIUM^® No. 63. All-In-One Wood Cleaner.  Lightly sand to remove remaining wood fibers/fuzz.
• Painted Surfaces-Wood: For a painted surface in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper to remove old coating. Scuff sand glossy surfaces. Use stainless steel or galvanized nails to prevent nail staining. Countersink nail heads, repair imperfections and sand smooth. Remove all dust with a damp cloth, allow to dry.
• Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer's label directions) to achieve a textured profile similar to 150 grit sandpaper. Wipe your fingers over the clean, dry floor to check for dust or powder. Ensure there is no residue on your fingers that may have been left from the etcher. If residue is found, rinse the surface to remove residue. Allow the surface to dry completely. Sprinkle a few drops of water onto the surface. If water is quickly absorbed and the surface feels like 150 grit sandpaper, the surface is ready. If not, re-etch.
• Painted Surfaces-Concrete: For a painted surface in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface. Scuff sand glossy surfaces. Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.

Prime

• Interior Wood: Use a product such as PREMIUM PLUS^® No. 75 All-In-One Primer & Sealer.
• Exterior Wood: Use a product such as PREMIUM PLUS^® No. 436 Multi-Surface Primer & Sealer.
• Interior/Exterior Concrete or Masonry: Over uncoated concrete or masonry surfaces, use a product such as BEHR PREMIUM No. 880 Concrete & Masonry Bonding Primer.

Application

• Use product when the surface and air temperatures are between 50-90°F (10-32°C).
• Stir paint occasionally.
• When working with more than one can of the same product, intermix to ensure color uniformity.
• Use a high quality 3/8 -1/2" nap roller cover, nylon/polyester brush or an airless sprayer (.015 - .021" spray tip, 60 mesh filter).
• Spread rate varies, depending on the surface texture, porosity and application method.
• Additional coats may be required to ensure proper coverage, optimal hide and durability.
• Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 1/2 pint per gallon.

Dry Time

• Longer dry time required in cooler temperatures and in higher humidity. Allow 72 hours before subjecting to normal use. After 30 days, cured paint film may be cleaned with a mild, non-abrasive liquid detergent. Dry paint film is mildew resistant.

Disposal

• Properly dispose of all soiled rags.
• For disposal of empty containers and unused product, contact your household refuse collection service.

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.