Fast Drying Water-Based Poly Urethane Aerosol Spray | Behr


Avg. Rating:

BEHR Fast Drying Water-Based Polyurethane Aerosol is a clear protective finish that shields your interior wood surfaces that are stained with BEHR Water-Based Wood Stain. This durable polyurethane is designed to prolong the life of your wood surface and create a smooth, lasting finish. This product enhances the look and color of your wood surface, allowing its true beauty to shine through. Multiple sheens are available depending on your desired look.

See Our Selection of Water-Based Wood Stains and Finishes

Aerosol can of Behr Fast Drying Water Based Poly Urethane, interior


Available in Matte, Satin, Semi-Gloss and Gloss Finishes

Best For Use In

Properly prepared Interior unfinished and finished wood surfaces such as furniture, moldings, cabinets, trim and doors.


15 - 20 Sq. Ft.

  • Icon of spray can spraying paint.

    3 Coats

  • Icon representing length and width dimensions to determine square footage

    Spread Rate:
    15-20 Sq. Ft.

  • Icon of cleaning paint brush under water faucet

    Soap & Water

CAUTION: Top coated surfaces may be slippery when wet.

Surface Preparation

  • For refinishing, remove all wax or cleaner build-up with a wax stripper or degreaser prior to sanding. 
  • Sand all surfaces in the direction of the wood grain to desired smoothness.
  • DO NOT USE steel wool.
  • Remove all dust from sanded surfaces and clean with a tack cloth.
  • If desired, apply BEHR® Wood Stain. Follow all label instructions.

Read More


Note: Above dry times are based on good ventilation, the temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure a satisfactory result.
  • Do not apply in direct sunlight or in temperatures below 55°F (10°C) or above 90°F (32°C).

  • Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use.

  • Protect adjacent areas from overspray. Wet overspray can be removed with soap and water.

  • Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes.

  • On unfinished wood, apply sufficient material to seal open joints, edges, and end-grain.

  • Apply thin coats to avoid runs and sags. Recoat within 1 hour. If unable to do so, wait a minimum of 72 hours, then lightly sand and recoat.

  • Apply at least 3 coats on unfinished wood and 2 coats on surfaces already finished.

  • After the final coat, allow at least 24 hours before normal use.

Read More

Nozzle Care

Do not stick a pin in spray button opening.
  • After each use, clear valve by holding can upside down and spraying until only clear gas comes out.

  • If the spray button becomes clogged, wear eye protection, wipe off button opening with lacquer thinner.

  • Do not stick a pin in spray button opening.

Read More

Read More



For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event this product proves to be defective within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Tahitian sky
Small Behr logoS480-5
What sheen do I need?
8 Oz. Sample
1 Gallon
1 Quart
5 Gallon
The following product(s) is required to properly prep uncoated and previously coated concrete surfaces.
Required product
The following product(s) is required to properly prep uncoated and previously coated concrete surfaces. Only available in store at Home Depot.
Required 3rd party product
The 9 in. x 1/4 in. Polyester Adhesive Roller Cover has a hard texture, making it ideal for applying all types of adhesives to smooth surfaces. It can be used for stippling and applying sand paints.
The following product(s) is recommended when a topcoat clear finish is desired.
The Home Depot logoSold Exclusively at The Home Depot