BEHR PREMIUM^® Interior/Exterior Concrete & Garage Self-Priming 1-Part Epoxy No. 900

Where to UseBlank space if empty.

Interior or Exterior surfaces such as: Porous Concrete, Masonry, Stone and Brick. Ideal for horizontal surfaces such as: Garage Floors, Driveways, Basement floors, Porches and Pool Decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to fork-lifts.

Usage SummaryBlank space if empty.

PreparationBlank space if empty.

• Proper Surface Preparation is Required.
• All surfaces must be clean, sound, dry and free of any dirt, oil and grease.

New and Uncoated Concrete or Masonry Surfaces:

• Allow new surfaces to cure 30 days.
• Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer's label directions) to achieve a textured profile similar to 150 grit sandpaper.
• Wipe your fingers over the clean, dry floor to check for dust or powder. Ensure there is no residue on your fingers that may have been left from the etcher. If residue is found, rinse the surface to remove residue. Allow the surface to dry completely. Sprinkle a few drops of water onto the surface. If water is quickly absorbed and the surface feels like 150 grit sandpaper, the surface is ready. If not, re-etch.
• Apply a Primer Coat: Apply 1 coat of BEHR PREMIUM® Concrete & Garage Self-Priming 1-Part Epoxy, or a product such as BEHR PREMIUM No. 880 Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.

Painted, Stained or Sealed Concrete:

• For a painted surface in sound condition, use a product to clean and prepare the surface.
• If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface.
• Scuff sand glossy surfaces.
• Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.
• Spot prime all bare concrete areas with BEHR PREMIUM Concrete & Garage Self-Priming 1-Part Epoxy or with a product such as BEHR PREMIUM No. 880 Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.

ApplicationBlank space if empty.

• DO NOT THIN.
• Intermix all cans of same product to ensure color uniformity.
• Stir before and occasionally during application. Use product when air and surface temperatures are between 50-90° F (10-32° C).
• Apply to dry concrete. Do not apply if rain or heavy dew is expected within 24 hours.
• Apply a thin, even coat using a 3/8" nap roller cover, nylon/polyester brush or an airless sprayer (.015"-.021" spray tip, 60 mesh filter).
• Allow first coat to dry before deciding if a second coat is necessary. Additional coats may be required for optimal hide and durability.
• For uniformity apply second coat in a criss-cross pattern.
• An annual touch-up may be required in areas subject to tire traffic.

Dry TimeBlank space if empty.

• Longer dry time required in cooler temperatures and in higher humidity.
• The floor may be subjected to light foot traffic after 24 hours.
• Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture.
• Allow 7 days before subjecting to automotive tires.
• Premature heavy traffic will cause paint failure requiring spot recoating.
• If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours.
• Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed.
• Abrasive cleaners and pressure-washers should be used carefully to avoid premature paint failure.

DisposalBlank space if empty.

• Properly dispose of all soiled rags.
• To recycle or properly dispose of product in your community, contact your household refuse collection service.

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.